using lptim1 to wake from stop2

Discussions and support about ChibiOS/HAL, the MCU Hardware Abstraction Layer.
geoffrey.brown
Posts: 75
Joined: Thu May 07, 2015 9:47 pm
Has thanked: 3 times
Been thanked: 11 times

using lptim1 to wake from stop2

Postby geoffrey.brown » Fri Mar 26, 2021 12:25 pm

This isn't an issue, more of a topic for more discussion. I've been building sub-gram dataloggers with stm32l4 processors for biologists studying songbirds. As you might image the biggest issue is energy -- getting a year out of a 5.5mAh battery is hard. A common use case is to power up a sensor, kick off a measurement and then wait for time to pass. During that waiting stop2 is ideal, the issue is waking. To do that I've been using the low power timer to trigger the wake up. Here's a code fragment illustrating how this works:

Code: Select all

 // enable lptim1
    // Enter Stop2 mode

    RCC->APB1ENR1 |= (1 << 31);
    LPTIM1->CR = 1;

    // Set up compare,count registers
    LPTIM1->ARR = ms + 1;
    LPTIM1->CMP = ms; // set compare register
    LPTIM1->CNT = 0;  // reset counter
   
    // enable external event

    EXTI->EMR2 |= STM32_EXT_LPTIM1_LINE;

    // enable interrupts in lptim1

    LPTIM1->IER = STM32_LPTIM_IER_CMPMIE;
    LPTIM1->CFGR = 0;

    // Start the counter in single mode

    LPTIM1->CR |= STM32_LPTIM_CR_SNGSTRT;

    // go into stop2 mode

    DBGMCU->CR = 0;
    MODIFY_REG(PWR->CR1, PWR_CR1_LPMS, PWR_CR1_LPMS_STOP2);

    SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));
    __SEV();
    __WFE();
    __WFE();

    // disable lptim and interrupt/event

    EXTI->EMR2 &= ~STM32_EXT_LPTIM1_LINE;
    LPTIM1->IER = 0;
    LPTIM1->ICR = 1;
    LPTIM1->CR = 0;
    RCC->APB1ENR1 &= ~(1 << 31);
    CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));


I should note that stop2 isn't perfect. I've found it necessary to disable/enable the SPI device before entering stop2. For reasons that I don't understand, i2c doesn't seem to require this. Also, I don't use the HAL spi driver with dma and all that -- in my application, the small amount of data transferred doesn't justify the overhead of setting up dma.

This seems to be a useful technique, but I admit my approach is completely ad-hoc and ripe for improvements

Geoffrey

User avatar
Giovanni
Site Admin
Posts: 13434
Joined: Wed May 27, 2009 8:48 am
Location: Salerno, Italy
Has thanked: 839 times
Been thanked: 732 times
Contact:

Re: using lptim1 to wake from stop2

Postby Giovanni » Fri Mar 26, 2021 1:44 pm

Hi,

Why the double __WFE() ?

Giovanni

geoffrey.brown
Posts: 75
Joined: Thu May 07, 2015 9:47 pm
Has thanked: 3 times
Been thanked: 11 times

Re: using lptim1 to wake from stop2

Postby geoffrey.brown » Fri Mar 26, 2021 5:59 pm

SEV
WFE
WFE

The SEV; WFE guarantees that there are no other events. I admit it seems strange, but I will say this idiom appears elsewhere -- for example the cube libraries.

It would be nice if there definitive guidance from ST on this


Geoffrey

User avatar
Giovanni
Site Admin
Posts: 13434
Joined: Wed May 27, 2009 8:48 am
Location: Salerno, Italy
Has thanked: 839 times
Been thanked: 732 times
Contact:

Re: using lptim1 to wake from stop2

Postby Giovanni » Fri Mar 26, 2021 6:23 pm

geoffrey.brown wrote:SEV
WFE
WFE

The SEV; WFE guarantees that there are no other events. I admit it seems strange, but I will say this idiom appears elsewhere -- for example the cube libraries.

It would be nice if there definitive guidance from ST on this


Geoffrey


It makes sense.

Giovanni


Return to “ChibiOS/HAL”

Who is online

Users browsing this forum: No registered users and 2 guests