Dear forum,
Hi. I need info's how to program STM32VLD discovery kit inside from the chibistudio. This kit works in WDA mode but it has ST-LINK v2 as well. Any tutorial about it? Have in mind that i only managed to program this kit only with the ST-LINK utility came from ST.com. TIA.
STM32VLD support
- Giovanni
- Site Admin
- Posts: 14455
- Joined: Wed May 27, 2009 8:48 am
- Location: Salerno, Italy
- Has thanked: 1076 times
- Been thanked: 922 times
- Contact:
Re: STM32VLD support
Hi,
There is a demo for that board in ChibiStudio under /demos/STM32/RT-STM32F100-DISCOVERY.
Guides and tutorials regarding ChibiStudio are on http://www.playembedded.org you may want to watch the introduction video tutorial.
Giovanni
There is a demo for that board in ChibiStudio under /demos/STM32/RT-STM32F100-DISCOVERY.
Guides and tutorials regarding ChibiStudio are on http://www.playembedded.org you may want to watch the introduction video tutorial.
Giovanni
Re: STM32VLD support
Thank you for reply,
i 've already did registration but no approve email received yet.
By the way if you can tell me whats wrong, here it is the console message i get when i try to build the project you mention.
I've tryed to link with st-link option and retrieve the board script file stm32vldiscovery.cfg
Open On-Chip Debugger 0.10.0+dev-00746-g8f518d359 (2019-03-14-17:18)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Warn : Interface already configured, ignoring
Error: already specified hl_layout stlink
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 1000 kHz
adapter_nsrst_delay: 100
none separate
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Info : Listening on port 6666 for tcl connections
Info : Listening on port 4444 for telnet connections
Info : clock speed 1000 kHz
Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED
Error: open failed
Any ideas what to do next?
i 've already did registration but no approve email received yet.
By the way if you can tell me whats wrong, here it is the console message i get when i try to build the project you mention.
I've tryed to link with st-link option and retrieve the board script file stm32vldiscovery.cfg
Open On-Chip Debugger 0.10.0+dev-00746-g8f518d359 (2019-03-14-17:18)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Warn : Interface already configured, ignoring
Error: already specified hl_layout stlink
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 1000 kHz
adapter_nsrst_delay: 100
none separate
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Info : Listening on port 6666 for tcl connections
Info : Listening on port 4444 for telnet connections
Info : clock speed 1000 kHz
Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED
Error: open failed
Any ideas what to do next?
- Giovanni
- Site Admin
- Posts: 14455
- Joined: Wed May 27, 2009 8:48 am
- Location: Salerno, Italy
- Has thanked: 1076 times
- Been thanked: 922 times
- Contact:
Who is online
Users browsing this forum: No registered users and 17 guests