I use STM32F401NUCLEO-64. By ST-LINK tool I read that the firmware version is: V2.J21.M5 STM32 Debug + Mass storage (in this regard when in
"firmware update" I do "connect the device" does not give me problems and it finds the firmware version). The following is the last loaded code but I think I ...
Search found 8 matches
- Mon Nov 21, 2016 12:09 am
- Forum: ChibiStudio
- Topic: Problems with openOCD
- Replies: 11
- Views: 11916
- Sun Nov 20, 2016 4:13 pm
- Forum: ChibiStudio
- Topic: Problems with openOCD
- Replies: 11
- Views: 11916
Re: Problems with openOCD
yes I know. I keep pressing the reset button (black button) while I try to connect the board but does not connect.
- Sun Nov 20, 2016 1:46 pm
- Forum: ChibiStudio
- Topic: Problems with openOCD
- Replies: 11
- Views: 11916
Re: Problems with openOCD
I already tried to connect under reset but when I select this option and then try to connect the ST-Link utility shows me the following message:
Can not connect to the target!
If you're trying to connect to an STM32W1xx device, please select Normal or hotplug from target-mode> Settings menu.
I see ...
Can not connect to the target!
If you're trying to connect to an STM32W1xx device, please select Normal or hotplug from target-mode> Settings menu.
I see ...
- Sun Nov 20, 2016 2:42 am
- Forum: STM32 Support
- Topic: facing problem with openOCD for F401RE
- Replies: 7
- Views: 4793
Re: facing problem with openOCD for F401RE
I tried the openocd provided by RoccoMarco but the problem persists while the link provided by ep.hobbyiest leads me to a blank page. However my problem might be different even though the message shown by Chibistudio is the same, because I can not connect even by ST-Link tool. My problem is ...
- Sun Nov 20, 2016 2:32 am
- Forum: ChibiStudio
- Topic: Problems with openOCD
- Replies: 11
- Views: 11916
Re: Problems with openOCD
I will also run as an administrator but the problem persists. I tried to connect via ST-Link tool but it responds with the following message: "Can not connect to the target." I checked the 3V3 pin of the core and actually delivers 3.3 V and this is a thing that makes me think that the USB cable is ...
- Fri Nov 18, 2016 12:50 am
- Forum: STM32 Support
- Topic: facing problem with openOCD for F401RE
- Replies: 7
- Views: 4793
Re: facing problem with openOCD for F401RE
Hello, Can I Know Which openOCD you used to solve the problem? I tried with all available openOCD but I have not solved
- Wed Nov 02, 2016 4:15 pm
- Forum: ChibiStudio
- Topic: Problems with openOCD
- Replies: 11
- Views: 11916
Re: Problems with openOCD
thanks for the reply.
When I tried to connect the target using the ST-LINK tool it did not work. However the drivers are installed. I tried reinstalling but the problem persists. I used chibistudio without problems before the last update of Windows 10. Could this be the problem?
When I tried to connect the target using the ST-LINK tool it did not work. However the drivers are installed. I tried reinstalling but the problem persists. I used chibistudio without problems before the last update of Windows 10. Could this be the problem?
- Tue Nov 01, 2016 2:21 pm
- Forum: ChibiStudio
- Topic: Problems with openOCD
- Replies: 11
- Views: 11916
Problems with openOCD
Hi,when I run openOCD on ST-Link V2-1 I read this message
Open On-Chip Debugger 0.10.0-dev-00107-ge4848fe (2015-11-13-11:49)
Licensed under GNU GPL v2
For bug reports, read
m
Warn : Interface already configured, ignoring
Error: already specified hl_layout stlink
Info : The selected transport took ...
Open On-Chip Debugger 0.10.0-dev-00107-ge4848fe (2015-11-13-11:49)
Licensed under GNU GPL v2
For bug reports, read
m
Warn : Interface already configured, ignoring
Error: already specified hl_layout stlink
Info : The selected transport took ...