ok i worked that one out thank you
now i only have this SD2 error
/*
* Activates the serial driver 1 using the driver default configuration.
* PA2(TX) and PA3(RX) are routed to USART2.
*/
sdStart(&SD2, NULL);
the SD2 shows a "could not be resolved" error
main
Code: Select all
/*
ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
2011 Giovanni Di Sirio.
This file is part of ChibiOS/RT.
ChibiOS/RT is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 3 of the License, or
(at your option) any later version.
ChibiOS/RT is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include "ch.h"
#include "hal.h"
#include "test.h"
static void pwmpcb(PWMDriver *pwmp);
static void adccb(ADCDriver *adcp, adcsample_t *buffer, size_t n);
static void spicb(SPIDriver *spip);
/* Total number of channels to be sampled by a single ADC operation.*/
#define ADC_GRP1_NUM_CHANNELS 2
/* Depth of the conversion buffer, channels are sampled four times each.*/
#define ADC_GRP1_BUF_DEPTH 4
/*
* ADC samples buffer.
*/
static adcsample_t samples[ADC_GRP1_NUM_CHANNELS * ADC_GRP1_BUF_DEPTH];
/*
* ADC conversion group.
* Mode: Linear buffer, 4 samples of 2 channels, SW triggered.
* Channels: IN11 (48 cycles sample time)
* Sensor (192 cycles sample time)
*/
static const ADCConversionGroup adcgrpcfg = {
FALSE,
ADC_GRP1_NUM_CHANNELS,
adccb,
NULL,
/* HW dependent part.*/
0,
ADC_CR2_SWSTART,
ADC_SMPR1_SMP_AN11(ADC_SAMPLE_56) | ADC_SMPR1_SMP_SENSOR(ADC_SAMPLE_144),
0,
ADC_SQR1_NUM_CH(ADC_GRP1_NUM_CHANNELS),
0,
ADC_SQR3_SQ2_N(ADC_CHANNEL_IN11) | ADC_SQR3_SQ1_N(ADC_CHANNEL_SENSOR)
};
/*
* PWM configuration structure.
* Cyclic callback enabled, channels 1 and 4 enabled without callbacks,
* the active state is a logic one.
*/
static PWMConfig pwmcfg = {
10000, /* 10KHz PWM clock frequency. */
10000, /* PWM period 1S (in ticks). */
pwmpcb,
{
{PWM_OUTPUT_ACTIVE_HIGH, NULL},
{PWM_OUTPUT_DISABLED, NULL},
{PWM_OUTPUT_DISABLED, NULL},
{PWM_OUTPUT_ACTIVE_HIGH, NULL}
},
/* HW dependent part.*/
0
};
/*
* SPI configuration structure.
* Maximum speed (12MHz), CPHA=0, CPOL=0, 16bits frames, MSb transmitted first.
* The slave select line is the pin GPIOA_SPI1NSS on the port GPIOA.
*/
static const SPIConfig spicfg = {
spicb,
/* HW dependent part.*/
GPIOB,
12,
SPI_CR1_DFF
};
/*
* PWM cyclic callback.
* A new ADC conversion is started.
*/
static void pwmpcb(PWMDriver *pwmp) {
(void)pwmp;
/* Starts an asynchronous ADC conversion operation, the conversion
will be executed in parallel to the current PWM cycle and will
terminate before the next PWM cycle.*/
chSysLockFromIsr();
adcStartConversionI(&ADCD1, &adcgrpcfg, samples, ADC_GRP1_BUF_DEPTH);
chSysUnlockFromIsr();
}
/*
* ADC end conversion callback.
* The PWM channels are reprogrammed using the latest ADC samples.
* The latest samples are transmitted into a single SPI transaction.
*/
void adccb(ADCDriver *adcp, adcsample_t *buffer, size_t n) {
(void) buffer; (void) n;
/* Note, only in the ADC_COMPLETE state because the ADC driver fires an
intermediate callback when the buffer is half full.*/
if (adcp->state == ADC_COMPLETE) {
adcsample_t avg_ch1, avg_ch2;
/* Calculates the average values from the ADC samples.*/
avg_ch1 = (samples[0] + samples[2] + samples[4] + samples[6]) / 4;
avg_ch2 = (samples[1] + samples[3] + samples[5] + samples[7]) / 4;
chSysLockFromIsr();
/* Changes the channels pulse width, the change will be effective
starting from the next cycle.*/
pwmEnableChannelI(&PWMD4, 0, PWM_FRACTION_TO_WIDTH(&PWMD4, 4096, avg_ch1));
pwmEnableChannelI(&PWMD4, 3, PWM_FRACTION_TO_WIDTH(&PWMD4, 4096, avg_ch2));
/* SPI slave selection and transmission start.*/
spiSelectI(&SPID2);
spiStartSendI(&SPID2, ADC_GRP1_NUM_CHANNELS * ADC_GRP1_BUF_DEPTH, samples);
chSysUnlockFromIsr();
}
}
/*
* SPI end transfer callback.
*/
static void spicb(SPIDriver *spip) {
/* On transfer end just releases the slave select line.*/
chSysLockFromIsr();
spiUnselectI(spip);
chSysUnlockFromIsr();
}
/*
* This is a periodic thread that does absolutely nothing except flashing
* a LED.
*/
static WORKING_AREA(waThread1, 128);
static msg_t Thread1(void *arg) {
(void)arg;
chRegSetThreadName("blinker");
while (TRUE) {
palSetPad(GPIOD, GPIOD_LED3); /* Orange. */
chThdSleepMilliseconds(500);
palClearPad(GPIOD, GPIOD_LED3); /* Orange. */
chThdSleepMilliseconds(500);
}
}
/*
* Application entry point.
*/
int main(void) {
/*
* System initializations.
* - HAL initialization, this also initializes the configured device drivers
* and performs the board-specific initializations.
* - Kernel initialization, the main() function becomes a thread and the
* RTOS is active.
*/
halInit();
chSysInit();
/*
* Activates the serial driver 1 using the driver default configuration.
* PA2(TX) and PA3(RX) are routed to USART2.
*/
sdStart(&SD2, NULL);
palSetPadMode(GPIOA, 2, PAL_MODE_ALTERNATE(7));
palSetPadMode(GPIOA, 3, PAL_MODE_ALTERNATE(7));
/*
* If the user button is pressed after the reset then the test suite is
* executed immediately before activating the various device drivers in
* order to not alter the benchmark scores.
*/
if (palReadPad(GPIOA, GPIOA_BUTTON))
TestThread(&SD2);
/*
* Initializes the SPI driver 2. The SPI2 signals are routed as follow:
* PB12 - NSS.
* PB13 - SCK.
* PB14 - MISO.
* PB15 - MOSI.
*/
spiStart(&SPID2, &spicfg);
palSetPad(GPIOB, 12);
palSetPadMode(GPIOB, 12, PAL_MODE_OUTPUT_PUSHPULL |
PAL_STM32_OSPEED_HIGHEST); /* NSS. */
palSetPadMode(GPIOB, 13, PAL_MODE_ALTERNATE(5) |
PAL_STM32_OSPEED_HIGHEST); /* SCK. */
palSetPadMode(GPIOB, 14, PAL_MODE_ALTERNATE(5)); /* MISO. */
palSetPadMode(GPIOB, 15, PAL_MODE_ALTERNATE(5) |
PAL_STM32_OSPEED_HIGHEST); /* MOSI. */
/*
* Initializes the ADC driver 1 and enable the thermal sensor.
* The pin PC0 on the port GPIOC is programmed as analog input.
*/
adcStart(&ADCD1, NULL);
adcSTM32EnableTSVREFE();
palSetPadMode(GPIOC, 1, PAL_MODE_INPUT_ANALOG);
/*
* Initializes the PWM driver 4, routes the TIM4 outputs to the board LEDs.
*/
pwmStart(&PWMD4, &pwmcfg);
palSetPadMode(GPIOD, GPIOD_LED4, PAL_MODE_ALTERNATE(2)); /* Green. */
palSetPadMode(GPIOD, GPIOD_LED6, PAL_MODE_ALTERNATE(2)); /* Blue. */
/*
* Creates the example thread.
*/
chThdCreateStatic(waThread1, sizeof(waThread1), NORMALPRIO, Thread1, NULL);
/*
* Normal main() thread activity, in this demo it does nothing except
* sleeping in a loop and check the button state, when the button is
* pressed the test procedure is launched with output on the serial
* driver 2.
*/
while (TRUE) {
if (palReadPad(GPIOA, GPIOA_BUTTON))
TestThread(&SD2);
chThdSleepMilliseconds(500);
}
}
halconf
Code: Select all
/*
ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
2011,2012 Giovanni Di Sirio.
This file is part of ChibiOS/RT.
ChibiOS/RT is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 3 of the License, or
(at your option) any later version.
ChibiOS/RT is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/**
* @file templates/halconf.h
* @brief HAL configuration header.
* @details HAL configuration file, this file allows to enable or disable the
* various device drivers from your application. You may also use
* this file in order to override the device drivers default settings.
*
* @addtogroup HAL_CONF
* @{
*/
#ifndef _HALCONF_H_
#define _HALCONF_H_
#include "mcuconf.h"
/**
* @name Drivers enable switches
*/
#if !defined(HAL_USE_TM) || defined(__DOXYGEN__)
#define HAL_USE_TM TRUE
#endif
/**
* @brief Enables the PAL subsystem.
*/
#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
#define HAL_USE_PAL TRUE
#endif
/**
* @brief Enables the ADC subsystem.
*/
#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
#define HAL_USE_ADC TRUE
#endif
/**
* @brief Enables the CAN subsystem.
*/
#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
#define HAL_USE_CAN FALSE
#endif
/**
* @brief Enables the EXT subsystem.
*/
#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
#define HAL_USE_EXT FALSE
#endif
/**
* @brief Enables the GPT subsystem.
*/
#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
#define HAL_USE_GPT FALSE
#endif
/**
* @brief Enables the I2C subsystem.
*/
#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
#define HAL_USE_I2C FALSE
#endif
/**
* @brief Enables the ICU subsystem.
*/
#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
#define HAL_USE_ICU FALSE
#endif
/**
* @brief Enables the MAC subsystem.
*/
#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
#define HAL_USE_MAC FALSE
#endif
/**
* @brief Enables the MMC_SPI subsystem.
*/
#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
#define HAL_USE_MMC_SPI TRUE
#endif
/**
* @brief Enables the PWM subsystem.
*/
#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
#define HAL_USE_PWM TRUE
#endif
/**
* @brief Enables the RTC subsystem.
*/
#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
#define HAL_USE_RTC FALSE
#endif
/**
* @brief Enables the SDC subsystem.
*/
#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
#define HAL_USE_SDC FALSE
#endif
/**
* @brief Enables the SERIAL subsystem.
*/
#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
#define HAL_USE_SERIAL FALSE
#endif
/**
* @brief Enables the SERIAL over USB subsystem.
*/
#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
#define HAL_USE_SERIAL_USB FALSE
#endif
/**
* @brief Enables the SPI subsystem.
*/
#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
#define HAL_USE_SPI TRUE
#endif
/**
* @brief Enables the UART subsystem.
*/
#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
#define HAL_USE_UART FALSE
#endif
/**
* @brief Enables the USB subsystem.
*/
#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
#define HAL_USE_USB FALSE
#endif
/** @} */
/*===========================================================================*/
/**
* @name ADC driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Enables synchronous APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
#define ADC_USE_WAIT TRUE
#endif
/**
* @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
#define ADC_USE_MUTUAL_EXCLUSION TRUE
#endif
/** @} */
/*===========================================================================*/
/**
* @name CAN driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Sleep mode related APIs inclusion switch.
*/
#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
#define CAN_USE_SLEEP_MODE TRUE
#endif
/** @} */
/*===========================================================================*/
/**
* @name I2C driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Enables the mutual exclusion APIs on the I2C bus.
*/
#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
#define I2C_USE_MUTUAL_EXCLUSION TRUE
#endif
/** @} */
/*===========================================================================*/
/**
* @name MAC driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Enables an event sources for incoming packets.
*/
#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
#define MAC_USE_EVENTS TRUE
#endif
/** @} */
/*===========================================================================*/
/**
* @name MMC_SPI driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Block size for MMC transfers.
*/
#if !defined(MMC_SECTOR_SIZE) || defined(__DOXYGEN__)
#define MMC_SECTOR_SIZE 512
#endif
/**
* @brief Delays insertions.
* @details If enabled this options inserts delays into the MMC waiting
* routines releasing some extra CPU time for the threads with
* lower priority, this may slow down the driver a bit however.
* This option is recommended also if the SPI driver does not
* use a DMA channel and heavily loads the CPU.
*/
#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
#define MMC_NICE_WAITING TRUE
#endif
/**
* @brief Number of positive insertion queries before generating the
* insertion event.
*/
#if !defined(MMC_POLLING_INTERVAL) || defined(__DOXYGEN__)
#define MMC_POLLING_INTERVAL 10
#endif
/**
* @brief Interval, in milliseconds, between insertion queries.
*/
#if !defined(MMC_POLLING_DELAY) || defined(__DOXYGEN__)
#define MMC_POLLING_DELAY 10
#endif
/**
* @brief Uses the SPI polled API for small data transfers.
* @details Polled transfers usually improve performance because it
* saves two context switches and interrupt servicing. Note
* that this option has no effect on large transfers which
* are always performed using DMAs/IRQs.
*/
#if !defined(MMC_USE_SPI_POLLING) || defined(__DOXYGEN__)
#define MMC_USE_SPI_POLLING TRUE
#endif
/** @} */
/*===========================================================================*/
/**
* @name SDC driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Number of initialization attempts before rejecting the card.
* @note Attempts are performed at 10mS intervals.
*/
#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
#define SDC_INIT_RETRY 100
#endif
/**
* @brief Include support for MMC cards.
* @note MMC support is not yet implemented so this option must be kept
* at @p FALSE.
*/
#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
#define SDC_MMC_SUPPORT FALSE
#endif
/**
* @brief Delays insertions.
* @details If enabled this options inserts delays into the MMC waiting
* routines releasing some extra CPU time for the threads with
* lower priority, this may slow down the driver a bit however.
*/
#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
#define SDC_NICE_WAITING TRUE
#endif
/** @} */
/*===========================================================================*/
/**
* @name SERIAL driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Default bit rate.
* @details Configuration parameter, this is the baud rate selected for the
* default configuration.
*/
#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
#define SERIAL_DEFAULT_BITRATE 38400
#endif
/**
* @brief Serial buffers size.
* @details Configuration parameter, you can change the depth of the queue
* buffers depending on the requirements of your application.
* @note The default is 64 bytes for both the transmission and receive
* buffers.
*/
#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
#define SERIAL_BUFFERS_SIZE 16
#endif
/** @} */
/*===========================================================================*/
/**
* @name SERIAL_USB driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Serial over USB buffers size.
* @details Configuration parameter, the buffer size must be a multiple of
* the USB data endpoint maximum packet size.
* @note The default is 64 bytes for both the transmission and receive
* buffers.
*/
#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
#define SERIAL_USB_BUFFERS_SIZE 64
#endif
/** @} */
/*===========================================================================*/
/**
* @name SPI driver related setting
* @{
*/
/*===========================================================================*/
/**
* @brief Enables synchronous APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
#define SPI_USE_WAIT TRUE
#endif
/**
* @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
#define SPI_USE_MUTUAL_EXCLUSION TRUE
#endif
/** @} */
#endif /* _HALCONF_H_ */
/** @} */
mcuconf
Code: Select all
/*
ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
2011,2012 Giovanni Di Sirio.
This file is part of ChibiOS/RT.
ChibiOS/RT is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 3 of the License, or
(at your option) any later version.
ChibiOS/RT is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/*
* STM32F4xx drivers configuration.
* The following settings override the default settings present in
* the various device driver implementation headers.
* Note that the settings for each driver only have effect if the whole
* driver is enabled in halconf.h.
*
* IRQ priorities:
* 15...0 Lowest...Highest.
*
* DMA priorities:
* 0...3 Lowest...Highest.
*/
#define STM32F4xx_MCUCONF
/*
* HAL driver system settings.
*/
#define STM32_NO_INIT FALSE
#define STM32_HSI_ENABLED TRUE
#define STM32_LSI_ENABLED TRUE
#define STM32_HSE_ENABLED TRUE
#define STM32_LSE_ENABLED FALSE
#define STM32_CLOCK48_REQUIRED TRUE
#define STM32_SW STM32_SW_PLL
#define STM32_PLLSRC STM32_PLLSRC_HSE
#define STM32_PLLM_VALUE 8
#define STM32_PLLN_VALUE 336
#define STM32_PLLP_VALUE 2
#define STM32_PLLQ_VALUE 7
#define STM32_HPRE STM32_HPRE_DIV1
#define STM32_PPRE1 STM32_PPRE1_DIV4
#define STM32_PPRE2 STM32_PPRE2_DIV2
#define STM32_RTCSEL STM32_RTCSEL_LSI
#define STM32_RTCPRE_VALUE 8
#define STM32_MCO1SEL STM32_MCO1SEL_HSI
#define STM32_MCO1PRE STM32_MCO1PRE_DIV1
#define STM32_MCO2SEL STM32_MCO2SEL_SYSCLK
#define STM32_MCO2PRE STM32_MCO2PRE_DIV5
#define STM32_I2SSRC STM32_I2SSRC_CKIN
#define STM32_PLLI2SN_VALUE 192
#define STM32_PLLI2SR_VALUE 5
#define STM32_VOS STM32_VOS_HIGH
#define STM32_PVD_ENABLE FALSE
#define STM32_PLS STM32_PLS_LEV0
/*
* ADC driver system settings.
*/
#define STM32_ADC_ADCPRE ADC_CCR_ADCPRE_DIV4
#define STM32_ADC_USE_ADC1 TRUE
#define STM32_ADC_USE_ADC2 TRUE
#define STM32_ADC_USE_ADC3 TRUE
#define STM32_ADC_ADC1_DMA_STREAM STM32_DMA_STREAM_ID(2, 4)
#define STM32_ADC_ADC2_DMA_STREAM STM32_DMA_STREAM_ID(2, 2)
#define STM32_ADC_ADC3_DMA_STREAM STM32_DMA_STREAM_ID(2, 1)
#define STM32_ADC_ADC1_DMA_PRIORITY 2
#define STM32_ADC_ADC2_DMA_PRIORITY 2
#define STM32_ADC_ADC3_DMA_PRIORITY 2
#define STM32_ADC_IRQ_PRIORITY 6
#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 6
#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY 6
#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY 6
/*
* CAN driver system settings.
*/
#define STM32_CAN_USE_CAN1 FALSE
#define STM32_CAN_USE_CAN2 FALSE
#define STM32_CAN_CAN1_IRQ_PRIORITY 11
#define STM32_CAN_CAN2_IRQ_PRIORITY 11
/*
* EXT driver system settings.
*/
#define STM32_EXT_EXTI0_IRQ_PRIORITY 6
#define STM32_EXT_EXTI1_IRQ_PRIORITY 6
#define STM32_EXT_EXTI2_IRQ_PRIORITY 6
#define STM32_EXT_EXTI3_IRQ_PRIORITY 6
#define STM32_EXT_EXTI4_IRQ_PRIORITY 6
#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6
#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6
#define STM32_EXT_EXTI16_IRQ_PRIORITY 6
#define STM32_EXT_EXTI17_IRQ_PRIORITY 15
#define STM32_EXT_EXTI18_IRQ_PRIORITY 6
#define STM32_EXT_EXTI19_IRQ_PRIORITY 6
#define STM32_EXT_EXTI20_IRQ_PRIORITY 6
#define STM32_EXT_EXTI21_IRQ_PRIORITY 15
#define STM32_EXT_EXTI22_IRQ_PRIORITY 15
/*
* GPT driver system settings.
*/
#define STM32_GPT_USE_TIM1 FALSE
#define STM32_GPT_USE_TIM2 FALSE
#define STM32_GPT_USE_TIM3 FALSE
#define STM32_GPT_USE_TIM4 FALSE
#define STM32_GPT_USE_TIM5 FALSE
#define STM32_GPT_USE_TIM8 FALSE
#define STM32_GPT_TIM1_IRQ_PRIORITY 7
#define STM32_GPT_TIM2_IRQ_PRIORITY 7
#define STM32_GPT_TIM3_IRQ_PRIORITY 7
#define STM32_GPT_TIM4_IRQ_PRIORITY 7
#define STM32_GPT_TIM5_IRQ_PRIORITY 7
#define STM32_GPT_TIM8_IRQ_PRIORITY 7
/*
* I2C driver system settings.
*/
#define STM32_I2C_USE_I2C1 FALSE
#define STM32_I2C_USE_I2C2 FALSE
#define STM32_I2C_USE_I2C3 FALSE
#define STM32_I2C_I2C1_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 0)
#define STM32_I2C_I2C1_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6)
#define STM32_I2C_I2C2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2)
#define STM32_I2C_I2C2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7)
#define STM32_I2C_I2C3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2)
#define STM32_I2C_I2C3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4)
#define STM32_I2C_I2C1_IRQ_PRIORITY 5
#define STM32_I2C_I2C2_IRQ_PRIORITY 5
#define STM32_I2C_I2C3_IRQ_PRIORITY 5
#define STM32_I2C_I2C1_DMA_PRIORITY 3
#define STM32_I2C_I2C2_DMA_PRIORITY 3
#define STM32_I2C_I2C3_DMA_PRIORITY 3
#define STM32_I2C_I2C1_DMA_ERROR_HOOK() chSysHalt()
#define STM32_I2C_I2C2_DMA_ERROR_HOOK() chSysHalt()
#define STM32_I2C_I2C3_DMA_ERROR_HOOK() chSysHalt()
/*
* ICU driver system settings.
*/
#define STM32_ICU_USE_TIM1 FALSE
#define STM32_ICU_USE_TIM2 FALSE
#define STM32_ICU_USE_TIM3 FALSE
#define STM32_ICU_USE_TIM4 FALSE
#define STM32_ICU_USE_TIM5 FALSE
#define STM32_ICU_USE_TIM8 FALSE
#define STM32_ICU_TIM1_IRQ_PRIORITY 7
#define STM32_ICU_TIM2_IRQ_PRIORITY 7
#define STM32_ICU_TIM3_IRQ_PRIORITY 7
#define STM32_ICU_TIM4_IRQ_PRIORITY 7
#define STM32_ICU_TIM5_IRQ_PRIORITY 7
#define STM32_ICU_TIM8_IRQ_PRIORITY 7
/*
* PWM driver system settings.
*/
#define STM32_PWM_USE_ADVANCED FALSE
#define STM32_PWM_USE_TIM1 TRUE
#define STM32_PWM_USE_TIM2 TRUE
#define STM32_PWM_USE_TIM3 FALSE
#define STM32_PWM_USE_TIM4 TRUE
#define STM32_PWM_USE_TIM5 FALSE
#define STM32_PWM_USE_TIM8 FALSE
#define STM32_PWM_TIM1_IRQ_PRIORITY 7
#define STM32_PWM_TIM2_IRQ_PRIORITY 7
#define STM32_PWM_TIM3_IRQ_PRIORITY 7
#define STM32_PWM_TIM4_IRQ_PRIORITY 7
#define STM32_PWM_TIM5_IRQ_PRIORITY 7
#define STM32_PWM_TIM8_IRQ_PRIORITY 7
/*
* SERIAL driver system settings.
*/
#define STM32_SERIAL_USE_USART1 FALSE
#define STM32_SERIAL_USE_USART2 FALSE
#define STM32_SERIAL_USE_USART3 FALSE
#define STM32_SERIAL_USE_UART4 FALSE
#define STM32_SERIAL_USE_UART5 FALSE
#define STM32_SERIAL_USE_USART6 FALSE
#define STM32_SERIAL_USART1_PRIORITY 12
#define STM32_SERIAL_USART2_PRIORITY 12
#define STM32_SERIAL_USART3_PRIORITY 12
#define STM32_SERIAL_UART4_PRIORITY 12
#define STM32_SERIAL_UART5_PRIORITY 12
#define STM32_SERIAL_USART6_PRIORITY 12
/*
* SPI driver system settings.
*/
#define STM32_SPI_USE_SPI1 FALSE
#define STM32_SPI_USE_SPI2 TRUE
#define STM32_SPI_USE_SPI3 FALSE
#define STM32_SPI_SPI1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 0)
#define STM32_SPI_SPI1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 3)
#define STM32_SPI_SPI2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3)
#define STM32_SPI_SPI2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4)
#define STM32_SPI_SPI3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 0)
#define STM32_SPI_SPI3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7)
#define STM32_SPI_SPI1_DMA_PRIORITY 1
#define STM32_SPI_SPI2_DMA_PRIORITY 1
#define STM32_SPI_SPI3_DMA_PRIORITY 1
#define STM32_SPI_SPI1_IRQ_PRIORITY 10
#define STM32_SPI_SPI2_IRQ_PRIORITY 10
#define STM32_SPI_SPI3_IRQ_PRIORITY 10
#define STM32_SPI_DMA_ERROR_HOOK(spip) chSysHalt()
/*
* UART driver system settings.
*/
#define STM32_UART_USE_USART1 FALSE
#define STM32_UART_USE_USART2 TRUE
#define STM32_UART_USE_USART3 FALSE
#define STM32_UART_USE_USART6 FALSE
#define STM32_UART_USART1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 5)
#define STM32_UART_USART1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 7)
#define STM32_UART_USART2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 5)
#define STM32_UART_USART2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6)
#define STM32_UART_USART3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 1)
#define STM32_UART_USART3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3)
#define STM32_UART_USART6_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 2)
#define STM32_UART_USART6_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 7)
#define STM32_UART_USART1_IRQ_PRIORITY 12
#define STM32_UART_USART2_IRQ_PRIORITY 12
#define STM32_UART_USART3_IRQ_PRIORITY 12
#define STM32_UART_USART6_IRQ_PRIORITY 12
#define STM32_UART_USART1_DMA_PRIORITY 0
#define STM32_UART_USART2_DMA_PRIORITY 0
#define STM32_UART_USART3_DMA_PRIORITY 0
#define STM32_UART_USART6_DMA_PRIORITY 0
#define STM32_UART_DMA_ERROR_HOOK(uartp) chSysHalt()
/*
* USB driver system settings.
*/
#define STM32_USB_USE_OTG1 FALSE
#define STM32_USB_USE_OTG2 FALSE
#define STM32_USB_OTG1_IRQ_PRIORITY 14
#define STM32_USB_OTG2_IRQ_PRIORITY 14
#define STM32_USB_OTG1_RX_FIFO_SIZE 512
#define STM32_USB_OTG2_RX_FIFO_SIZE 1024
#define STM32_USB_OTG_THREAD_PRIO LOWPRIO
#define STM32_USB_OTG_THREAD_STACK_SIZE 128
#define STM32_USB_OTGFIFO_FILL_BASEPRI 0
compiler output
Code: Select all
02:20:11 **** Incremental Build of configuration ADC for project acd ****
make all
Compiling ../../../test/test.c
Compiling ../../../os/hal/src/hal.c
Compiling ../../../os/hal/src/adc.c
Compiling ../../../os/hal/src/can.c
Compiling ../../../os/hal/src/ext.c
Compiling ../../../os/hal/src/gpt.c
Compiling ../../../os/hal/src/i2c.c
Compiling ../../../os/hal/src/icu.c
Compiling ../../../os/hal/src/mac.c
Compiling ../../../os/hal/src/mmc_spi.c
Compiling ../../../os/hal/src/mmcsd.c
Compiling ../../../os/hal/src/pal.c
Compiling ../../../os/hal/src/pwm.c
Compiling ../../../os/hal/src/rtc.c
Compiling ../../../os/hal/src/sdc.c
Compiling ../../../os/hal/src/serial.c
Compiling ../../../os/hal/src/serial_usb.c
Compiling ../../../os/hal/src/spi.c
Compiling ../../../os/hal/src/tm.c
Compiling ../../../os/hal/src/uart.c
Compiling ../../../os/hal/src/usb.c
Compiling ../../../os/hal/platforms/STM32F4xx/stm32_dma.c
Compiling ../../../os/hal/platforms/STM32F4xx/hal_lld.c
Compiling ../../../os/hal/platforms/STM32F4xx/adc_lld.c
Compiling ../../../os/hal/platforms/STM32F4xx/ext_lld_isr.c
Compiling ../../../os/hal/platforms/STM32/can_lld.c
Compiling ../../../os/hal/platforms/STM32/ext_lld.c
Compiling ../../../os/hal/platforms/STM32/gpt_lld.c
Compiling ../../../os/hal/platforms/STM32/icu_lld.c
Compiling ../../../os/hal/platforms/STM32/mac_lld.c
Compiling ../../../os/hal/platforms/STM32/pwm_lld.c
Compiling ../../../os/hal/platforms/STM32/sdc_lld.c
Compiling ../../../os/hal/platforms/STM32/serial_lld.c
Compiling ../../../os/hal/platforms/STM32/spi_lld.c
Compiling ../../../os/hal/platforms/STM32/GPIOv2/pal_lld.c
Compiling ../../../os/hal/platforms/STM32/I2Cv1/i2c_lld.c
Compiling ../../../os/hal/platforms/STM32/OTGv1/usb_lld.c
Compiling ../../../os/hal/platforms/STM32/RTCv2/rtc_lld.c
Compiling ../../../os/hal/platforms/STM32/USARTv1/uart_lld.c
Compiling ../../../boards/ST_STM32F4_DISCOVERY/board.c
Compiling main.c
main.c: In function 'Thread1':
main.c:166:1: warning: no return statement in function returning non-void [-Wreturn-type]
main.c: In function 'main':
main.c:187:3: warning: implicit declaration of function 'sdStart' [-Wimplicit-function-declaration]
main.c:187:12: error: 'SD2' undeclared (first use in this function)
main.c:187:12: note: each undeclared identifier is reported only once for each function it appears in
make: *** [build/obj/main.o] Error 1
02:20:20 Build Finished (took 8s.363ms)
