Serial Driver on USART2 TX not working
Posted: Thu Apr 02, 2015 10:04 pm
I recently rewrote a portion of code to use the Serial Driver (SD2) instead of the USART driver to avoid a DMA conflict. Using a logic analyzer I discovered that while RX works, the TX line is completely silent. I then tried SD6 instead, and both RX and TX work just fine. I know the pin configuration for USART2 is correct since I successfully used the USART driver on that port. I realize that USART6 and USART2 are clocked from different sources, so I made sure that both were running at the same speed. I've got all the debug options turned on but no errors are generated. Furthermore, I set up a thread to catch serial events while my main thread writes to SD2 and I successfully catch the CHN_OUTPUT_EMPTY followed by CHN_TRANSMISSION_END despite no data actually showing up on TX.
I'm using ChibiOS 3 pulled from master a few days ago, and my board is a STM32F411RE Nucleo. I'll post the relevant code below, but let me know if there is anything else I should provide.
main.c
mcuconf.c
I'm using ChibiOS 3 pulled from master a few days ago, and my board is a STM32F411RE Nucleo. I'll post the relevant code below, but let me know if there is anything else I should provide.
main.c
Code: Select all
static THD_WORKING_AREA(bleSerialEventThreadWA, 256);
static msg_t bleSerialEventThread(void* arg);
int main(void) {
halInit();
chSysInit();
chThdCreateStatic(bleSerialEventThreadWA, sizeof(bleSerialEventThreadWA), NORMALPRIO, bleSerialEventThread, NULL);
//sdStart(&SD6, NULL);
//palSetPadMode(GPIOA, 11, PAL_MODE_ALTERNATE(8));
//palSetPadMode(GPIOA, 12, PAL_MODE_ALTERNATE(8));
sdStart(&SD2, NULL);
palSetPadMode(GPIOA, 2 , PAL_MODE_ALTERNATE(7));
palSetPadMode(GPIOA, 3 , PAL_MODE_ALTERNATE(7));
while (TRUE)
{
chThdSleepMilliseconds(500);
sdPut(&SD2, 'A');
//sdPut(&SD6, 'A');
}
}
static msg_t bleSerialEventThread(void* arg)
{
(void)arg;
event_listener_t listener;
eventflags_t flags;
chEvtRegisterMask((event_source_t *)chnGetEventSource(&SD2), &listener, EVENT_MASK(1));
for (;;)
{
chEvtWaitOne(EVENT_MASK(1));
chSysLock();
flags = chEvtGetAndClearFlagsI(&listener);
chSysUnlock();
}
return MSG_OK;
}
mcuconf.c
Code: Select all
/*
* STM32F4xx drivers configuration.
* The following settings override the default settings present in
* the various device driver implementation headers.
* Note that the settings for each driver only have effect if the whole
* driver is enabled in halconf.h.
*
* IRQ priorities:
* 15...0 Lowest...Highest.
*
* DMA priorities:
* 0...3 Lowest...Highest.
*/
#define STM32F4xx_MCUCONF
/*
* HAL driver system settings.
*/
#define STM32_NO_INIT FALSE
#define STM32_HSI_ENABLED TRUE
#define STM32_LSI_ENABLED TRUE
#define STM32_HSE_ENABLED FALSE
#define STM32_LSE_ENABLED FALSE
#define STM32_CLOCK48_REQUIRED TRUE
#define STM32_SW STM32_SW_PLL
#define STM32_PLLSRC STM32_PLLSRC_HSI
#define STM32_PLLM_VALUE 16
#define STM32_PLLN_VALUE 384
#define STM32_PLLP_VALUE 4
#define STM32_PLLQ_VALUE 8
#define STM32_HPRE STM32_HPRE_DIV1
#define STM32_PPRE1 STM32_PPRE1_DIV4
#define STM32_PPRE2 STM32_PPRE2_DIV4
#define STM32_RTCSEL STM32_RTCSEL_LSI
#define STM32_RTCPRE_VALUE 8
#define STM32_MCO1SEL STM32_MCO1SEL_HSI
#define STM32_MCO1PRE STM32_MCO1PRE_DIV1
#define STM32_MCO2SEL STM32_MCO2SEL_SYSCLK
#define STM32_MCO2PRE STM32_MCO2PRE_DIV5
#define STM32_I2SSRC STM32_I2SSRC_CKIN
#define STM32_PLLI2SN_VALUE 192
#define STM32_PLLI2SR_VALUE 5
#define STM32_PVD_ENABLE FALSE
#define STM32_PLS STM32_PLS_LEV0
#define STM32_BKPRAM_ENABLE FALSE
/*
* ADC driver system settings.
*/
#define STM32_ADC_ADCPRE ADC_CCR_ADCPRE_DIV4
#define STM32_ADC_USE_ADC1 TRUE
#define STM32_ADC_ADC1_DMA_STREAM STM32_DMA_STREAM_ID(2, 4)
#define STM32_ADC_ADC1_DMA_PRIORITY 2
#define STM32_ADC_IRQ_PRIORITY 6
#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 6
/*
* EXT driver system settings.
*/
#define STM32_EXT_EXTI0_IRQ_PRIORITY 6
#define STM32_EXT_EXTI1_IRQ_PRIORITY 6
#define STM32_EXT_EXTI2_IRQ_PRIORITY 6
#define STM32_EXT_EXTI3_IRQ_PRIORITY 6
#define STM32_EXT_EXTI4_IRQ_PRIORITY 6
#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6
#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6
#define STM32_EXT_EXTI16_IRQ_PRIORITY 6
#define STM32_EXT_EXTI17_IRQ_PRIORITY 15
#define STM32_EXT_EXTI18_IRQ_PRIORITY 6
#define STM32_EXT_EXTI19_IRQ_PRIORITY 6
#define STM32_EXT_EXTI22_IRQ_PRIORITY 15
/*
* GPT driver system settings.
*/
#define STM32_GPT_USE_TIM1 FALSE
#define STM32_GPT_USE_TIM2 FALSE
#define STM32_GPT_USE_TIM3 FALSE
#define STM32_GPT_USE_TIM4 FALSE
#define STM32_GPT_USE_TIM5 FALSE
#define STM32_GPT_USE_TIM9 FALSE
#define STM32_GPT_USE_TIM11 FALSE
#define STM32_GPT_TIM1_IRQ_PRIORITY 7
#define STM32_GPT_TIM2_IRQ_PRIORITY 7
#define STM32_GPT_TIM3_IRQ_PRIORITY 7
#define STM32_GPT_TIM4_IRQ_PRIORITY 7
#define STM32_GPT_TIM5_IRQ_PRIORITY 7
#define STM32_GPT_TIM9_IRQ_PRIORITY 7
#define STM32_GPT_TIM11_IRQ_PRIORITY 7
/*
* I2C driver system settings.
*/
#define STM32_I2C_USE_I2C1 FALSE
#define STM32_I2C_USE_I2C2 TRUE
#define STM32_I2C_USE_I2C3 TRUE
#define STM32_I2C_BUSY_TIMEOUT 50
#define STM32_I2C_I2C1_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 0)
#define STM32_I2C_I2C1_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6)
#define STM32_I2C_I2C2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3)
#define STM32_I2C_I2C2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7)
#define STM32_I2C_I2C3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2)
#define STM32_I2C_I2C3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4)
#define STM32_I2C_I2C1_IRQ_PRIORITY 5
#define STM32_I2C_I2C2_IRQ_PRIORITY 5
#define STM32_I2C_I2C3_IRQ_PRIORITY 5
#define STM32_I2C_I2C1_DMA_PRIORITY 3
#define STM32_I2C_I2C2_DMA_PRIORITY 3
#define STM32_I2C_I2C3_DMA_PRIORITY 3
#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure")
/*
* ICU driver system settings.
*/
#define STM32_ICU_USE_TIM1 FALSE
#define STM32_ICU_USE_TIM2 FALSE
#define STM32_ICU_USE_TIM3 FALSE
#define STM32_ICU_USE_TIM4 FALSE
#define STM32_ICU_USE_TIM5 FALSE
#define STM32_ICU_USE_TIM9 FALSE
#define STM32_ICU_TIM1_IRQ_PRIORITY 7
#define STM32_ICU_TIM2_IRQ_PRIORITY 7
#define STM32_ICU_TIM3_IRQ_PRIORITY 7
#define STM32_ICU_TIM4_IRQ_PRIORITY 7
#define STM32_ICU_TIM5_IRQ_PRIORITY 7
#define STM32_ICU_TIM9_IRQ_PRIORITY 7
/*
* PWM driver system settings.
*/
#define STM32_PWM_USE_ADVANCED FALSE
#define STM32_PWM_USE_TIM1 FALSE
#define STM32_PWM_USE_TIM2 FALSE
#define STM32_PWM_USE_TIM3 TRUE
#define STM32_PWM_USE_TIM4 FALSE
#define STM32_PWM_USE_TIM5 FALSE
#define STM32_PWM_USE_TIM9 FALSE
#define STM32_PWM_TIM1_IRQ_PRIORITY 7
#define STM32_PWM_TIM2_IRQ_PRIORITY 7
#define STM32_PWM_TIM3_IRQ_PRIORITY 7
#define STM32_PWM_TIM4_IRQ_PRIORITY 7
#define STM32_PWM_TIM5_IRQ_PRIORITY 7
#define STM32_PWM_TIM9_IRQ_PRIORITY 7
/*
* SDC driver system settings.
*/
#define STM32_SDC_SDIO_DMA_PRIORITY 3
#define STM32_SDC_SDIO_IRQ_PRIORITY 9
#define STM32_SDC_WRITE_TIMEOUT_MS 250
#define STM32_SDC_READ_TIMEOUT_MS 25
#define STM32_SDC_CLOCK_ACTIVATION_DELAY 10
#define STM32_SDC_SDIO_UNALIGNED_SUPPORT TRUE
#define STM32_SDC_SDIO_DMA_STREAM STM32_DMA_STREAM_ID(2, 3)
/*
* SERIAL driver system settings.
*/
#define STM32_SERIAL_USE_USART1 FALSE
#define STM32_SERIAL_USE_USART2 TRUE
#define STM32_SERIAL_USE_USART6 TRUE
#define STM32_SERIAL_USART1_PRIORITY 12
#define STM32_SERIAL_USART2_PRIORITY 12
#define STM32_SERIAL_USART6_PRIORITY 12
/*
* SPI driver system settings.
*/
#define STM32_SPI_USE_SPI1 FALSE
#define STM32_SPI_USE_SPI2 FALSE
#define STM32_SPI_USE_SPI3 FALSE
#define STM32_SPI_SPI1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 0)
#define STM32_SPI_SPI1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 3)
#define STM32_SPI_SPI2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3)
#define STM32_SPI_SPI2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4)
#define STM32_SPI_SPI3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 0)
#define STM32_SPI_SPI3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7)
#define STM32_SPI_SPI1_DMA_PRIORITY 1
#define STM32_SPI_SPI2_DMA_PRIORITY 1
#define STM32_SPI_SPI3_DMA_PRIORITY 1
#define STM32_SPI_SPI1_IRQ_PRIORITY 10
#define STM32_SPI_SPI2_IRQ_PRIORITY 10
#define STM32_SPI_SPI3_IRQ_PRIORITY 10
#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure")
/*
* ST driver system settings.
*/
#define STM32_ST_IRQ_PRIORITY 8
#define STM32_ST_USE_TIMER 2
/*
* UART driver system settings.
*/
#define STM32_UART_USE_USART1 TRUE
#define STM32_UART_USE_USART2 FALSE
#define STM32_UART_USE_USART6 FALSE
#define STM32_UART_USART1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 5)
#define STM32_UART_USART1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 7)
#define STM32_UART_USART2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 5)
#define STM32_UART_USART2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6)
#define STM32_UART_USART6_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 2)
#define STM32_UART_USART6_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 6)
#define STM32_UART_USART1_IRQ_PRIORITY 12
#define STM32_UART_USART2_IRQ_PRIORITY 12
#define STM32_UART_USART6_IRQ_PRIORITY 12
#define STM32_UART_USART1_DMA_PRIORITY 0
#define STM32_UART_USART2_DMA_PRIORITY 0
#define STM32_UART_USART6_DMA_PRIORITY 0
#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure")
/*
* USB driver system settings.
*/
#define STM32_USB_USE_OTG1 TRUE
#define STM32_USB_OTG1_IRQ_PRIORITY 14
#define STM32_USB_OTG1_RX_FIFO_SIZE 512
#define STM32_USB_OTG_THREAD_PRIO LOWPRIO
#define STM32_USB_OTG_THREAD_STACK_SIZE 128
#define STM32_USB_OTGFIFO_FILL_BASEPRI 0